Signal Classification Software: Making Sense of Detected RF Emissions

August 13, 2026
|

A spectrum display can show where an emission appears in frequency, how wide it is and how strong it is at the receiver. Signal classification software analyses those measurements and other observable features to estimate what type of radio frequency (RF) signal was detected. The result helps operators decide which emissions to investigate, compare with authorised activity or locate using direction finding.

Detection, characterisation, classification and identification

  • Detection establishes that a signal is present in a monitored band, for example when the measured level exceeds a configured threshold.
  • Characterisation measures observable features such as centre frequency, occupied bandwidth, received signal level, timing and duration.
  • Classification assigns a likely signal type using measured features, reference profiles or a trained classifier.
  • Identification associates the signal with a specific transmitter or device where sufficient evidence is available. This may require decoded identifiers, equipment records or corroborating observations.

Automating characterisation and classification helps monitoring teams review more detections and focus analyst time on unfamiliar or ambiguous emissions.

Why classification is difficult in dense electromagnetic environments

Several signals can occupy the same band or exhibit similar bandwidth and timing. Weak or intermittent transmissions may be captured only in part, while noise, interference and propagation effects can obscure the features used for classification.

In defence and security applications, low-power, short-duration or frequency-agile transmissions can be particularly challenging to capture. Classification performance depends on what the sensor records and how well the classifier represents the signals it encounters.

Signal parameters used in classification

Useful features include centre frequency and its change over time, occupied bandwidth, received signal level, burst duration, repetition rate, and duty cycle. Spectrum traces show signal energy across frequency. Waterfall displays add a time dimension, helping analysts examine patterns such as recurring bursts or frequency changes.

In-phase and quadrature (IQ) samples preserve amplitude and phase information within the recorded bandwidth. Where the recording quality and analysis tools permit, IQ data can support modulation analysis, waveform comparison and demodulation. ICS Monitoring supports spectrum trace, waterfall and IQ recording for subsequent analysis. ICS Monitoring

Comparing signals against known transmitter profiles

One approach to automated RF signal classification is to compare a detection with reference profiles. A profile can describe the expected frequency range, bandwidth and timing of a signal type. Received power can provide context, although it also depends on factors such as distance, propagation and the receiving antenna.

When a classifier reports a score, operators should interpret it based on what the system measures. A close profile match can help prioritise a detection for review. An ambiguous match may require a longer capture, additional measurements or comparison with other observations.

ICS Monitoring supports automated signal classification, including UAV identification. Its Electronic Warfare Map helps operators view detected activity and available emitter locations in their operational context. ATDI defence spectrum management

Classifying complex emissions

AM and FM describe modulation methods. TETRA and LTE are communications standards whose signals can exhibit different characteristics depending on the configuration. In each case, classification depends on which features are visible in the recording.

Frequency-hopping signals change frequency according to the waveform’s design, so a single spectrum trace may capture only one part of the pattern. Chirp signals sweep through a range of frequencies. A time-frequency recording can help reveal hopping or sweep behaviour when it captures enough of the transmission. These observations can guide further investigation in communications intelligence (COMINT) workflows. ATDI signal interception and localisation

How AI helps group related RF measurements

A single transmitter can produce repeated detections over time. Grouping related measurements helps operators review activity that may come from the same source, particularly when several emissions are present in the same band.

ICS Monitoring uses AI-based clustering to group direction-finding measurements for analysis. Operators can examine the resulting groups alongside signal characteristics, timing and available location estimates. In ATDI’s wider defence workflow, HiNT provides AI-assisted analysis to help operators query RF data and interpret signals and emitters of interest. ICS Monitoring · ATDI defence spectrum management

Automated and operator-assisted classification

Automated classification can flag likely matches as monitoring data arrives. Operators can review uncertain or unfamiliar emissions using spectrum traces, waterfall recordings, available IQ samples and contextual information. If the evidence is insufficient, the team can leave the signal unclassified while it collects more data.

Using classification to guide investigations

For spectrum compliance, a likely signal type can help an operator find the relevant licence record and compare measured parameters with authorised conditions. In counter-UAS operations, a suspected drone link can prompt a review of the alert and corroboration from another sensor. In COMINT, a likely signal type can help prioritise an emission for further analysis or localisation.

Copyright © 2026 All Rights Reserved Privacy PolicyTerms and Conditions
Site designed by Fortico
Contact us

Request a software trial or demo

Register to receive a free trial licence or no obligation demo
Trial Licence
Request a demo
magnifiercrosschevron-down