Electricity substations, water pumping stations and pipeline monitoring sites can be separated by long distances and difficult terrain. The communications networks that connect them support remote monitoring and control, fault detection, field operations, and smart metering.
Utility communications network planning helps engineers determine how to connect each asset and how to maintain essential services if a site or link fails.
Utility coverage follows asset locations and field operations. A substation in a remote valley, a pumping station on a hilltop and a meter in a below-ground chamber each present different radio propagation challenges.
Service requirements vary by application. A protection or control circuit may require stringent availability and latency targets, while a meter that sends periodic readings can tolerate longer delays. These differences inform technology choices, coverage targets, and backup arrangements.
Utilities often combine wireless and wired infrastructure. The wireless technologies used depend on the service, location, and required capacity.
For smart metering, the design must account for where meters are installed, how often they report and how many devices share the available capacity. ATDI radio network planning for utilities · LoRaWAN for smart utilities
Terrain, buildings, vegetation and installation conditions affect how reliably a radio signal reaches a utility asset. Engineers can use RF propagation modelling to compare candidate sites and antenna heights, identify potential coverage gaps and prioritise locations for field measurements. Capacity planning then checks whether the proposed network can handle the expected traffic from the assets it serves.
HTZ Communications supports radio network planning from a few kHz to 1 THz, with more than 50 empirical, deterministic and hybrid propagation models. Engineers can use the same planning platform to study microwave links, VHF/UHF coverage and private LTE or 5G networks, selecting a model suited to the frequency, terrain and application. HTZ Communications
Where a network uses licensed spectrum, engineers need to check which frequencies are available and what coordination and licence conditions apply. Frequency planning also considers potential interference between the utility’s own sites and other users operating on the same or adjacent channels.
HTZ Communications supports automated frequency assignment and interference analysis. Engineers can use these tools to evaluate candidate assignments against defined compatibility criteria, assess predicted interference and identify assignments that need further coordination. HTZ Communications
In an RF mesh network, devices may relay traffic through other nodes to reach a gateway. Engineers assess available paths, how many hops a connection requires, and whether alternative paths exist if a relay fails. In point-to-multipoint networks, multiple endpoints communicate with a common base station. LoRaWAN typically uses a star-of-stars topology, where an end device can transmit directly to one or more gateways. LoRaWAN network architecture
HTZ Communications supports automated gateway selection for mesh and clustered networks. Engineers can compare candidate locations and estimate how many gateways are needed to meet a defined coverage target. For example, Australian IoT network operator NNNCo uses HTZ Communications to assess LoRaWAN coverage for underground water meters and pole-mounted monitoring devices. ATDI utility planning capabilities · NNNCo smart water metering example
Point-to-point microwave can connect remote utility sites to control infrastructure where fibre is unavailable or where the design calls for a separate backhaul path. Engineers assess line of sight, Fresnel zone clearance, interference and predicted link availability. Depending on the frequency, path length and local conditions, rain attenuation and multipath fading can affect availability. ITU-R P.530 for terrestrial line-of-sight systems
Proposed wind turbines can affect nearby microwave or telemetry links through obstruction, diffraction or reflection, depending on their position relative to the radio path. HTZ Communications supports wind farm coordination studies so engineers can assess potential effects on existing links before construction. ATDI wind farm and microwave link assessment
Resilience planning starts by identifying which services must continue if a radio site, backhaul link or power supply fails. Engineers can compare RF coverage with a candidate site excluded and assess whether the remaining sites can still serve priority assets. They can also review whether an alternative backhaul route has sufficient capacity to carry critical traffic during an outage.
Two routes can appear separate on a map while sharing a mast, power supply or network node. Checking these dependencies alongside RF coverage and link availability helps utilities identify where a single failure could affect both routes.
HTZ’s AI Mask Prediction uses satellite imagery to identify features such as trees and buildings that can affect radio propagation. Engineers can use those features to prepare or refine a clutter layer, which represents objects and land cover that can affect signal strength. This is useful when assessing long utility corridors or dispersed assets where existing map data may lack local detail. The resulting map data feeds into the RF propagation model, and field measurements can help check predictions at critical sites. HTZ AI Mask Prediction
A utility may use microwave for backhaul, private LTE for field data, TETRA for operational voice and LoRaWAN for remote metering. Each network has different coverage, capacity and availability targets. Planning them in a common RF environment helps engineers compare coverage across the same assets and assess coexistence where frequencies or sites are shared.
HTZ Communications brings coverage prediction, microwave path analysis and frequency planning into one platform for utility engineers designing or upgrading networks across multiple technologies. Explore HTZ Communications




