Indoor Propagation Modelling Software: Predicting RF Coverage Inside Buildings

August 6, 2026
|

A strong signal outside a building does not guarantee reliable coverage inside. Walls, floors, glazing and building geometry affect how radio signals enter and travel through a building. Indoor propagation modelling software predicts RF coverage before installation, helping engineers compare antenna layouts and identify areas that may need additional coverage.

Why indoor propagation differs from outdoor propagation

Outdoor coverage depends on factors such as terrain, clutter and link geometry. For outdoor-to-indoor coverage, engineers must also account for building entry loss, the additional attenuation associated with reception inside a building. Inside the building, walls and floors can attenuate signals, while corridors and open spaces can reflect them.

Penetration loss depends on the frequency, and the effect also depends on the material, its construction and the signal path. An outdoor coverage map that omits building entry loss can therefore overestimate the signal available to indoor users. ITU-R P.2109 on building entry loss

Construction materials and attenuation

Reinforced concrete, metal cladding, foil-backed insulation and some coated glazing can significantly reduce signal levels. Lightweight partitions often introduce less attenuation, although losses vary with thickness, composition and frequency.

HTZ Communications lets engineers specify building materials for indoor studies. The appropriate propagation model depends on the scenario. ITU-R P.2040 describes how building materials and structures affect radio waves, ITU-R P.2109 provides a statistical estimate of building entry loss, and 3GPP TR 38.901 includes models for defined indoor and outdoor-to-indoor scenarios. ATDI indoor modelling for aviation · ITU-R P.2040 · 3GPP TR 38.901

Building representation and floor plans

Floor plans show the layout of rooms, walls, corridors and open spaces. Floor elevations and ceiling heights add the vertical detail needed to assess coverage between levels. In a site-specific study, engineers can use architectural drawings, digital floor plans or survey data to represent the building geometry and assign materials to relevant surfaces.

The level of detail should match the study. In an airport terminal, for example, modelling an atrium or a partition between public and operational areas can help explain why coverage differs across floors or adjoining spaces.

Indoor-to-indoor and outdoor-to-indoor coverage

  • Outdoor-to-indoor (O2I) modelling estimates coverage from an outdoor transmitter inside a building. The calculation accounts for the outdoor path, building entry loss and, where the selected model represents it separately, propagation within the building.
  • Indoor-to-indoor modelling predicts coverage from an access point, small cell or distributed antenna system inside the building. The study can account for losses through walls and floors, as well as paths through open areas.

Both scenarios can apply at the same site. Outdoor macro cells may provide sufficient coverage near windows and entrances, while internal rooms or lower floors may need dedicated indoor equipment.

Antenna placement and coverage gap identification

Engineers can calculate coverage for candidate antenna or access point locations and compare predicted signal levels floor by floor. Comparing those results with the network’s design targets shows where the proposed layout is likely to leave gaps.

Before installation, teams can test changes to antenna position, mounting height or transmit power and assess whether an additional access point is needed. Where services share spectrum or overlap, interference analysis can help determine whether a layout will deliver the required service quality. HTZ Communications

Technologies supported

HTZ Communications supports indoor and mixed indoor–outdoor planning for technologies including Wi-Fi, LTE, 5G and TETRA. At an airport, engineers can assess passenger Wi-Fi, public mobile coverage and operational radio services within the same site, using the frequencies and coverage targets relevant to each network.

For private LTE and 5G in factories, warehouses and hospitals, coverage and capacity are related design questions. Building layout, materials and operating frequency affect signal propagation. Device density, traffic demand and service requirements inform capacity planning. HTZ Communications

Pre-deployment modelling and post-installation surveys

Pre-deployment modelling helps engineers compare designs while antenna locations and equipment choices are still flexible. Post-installation measurements verify how the installed network performs against its acceptance criteria. The extent of the survey depends on the service requirements, the building and the confidence needed in the results. Measurements can also help engineers tune the propagation model and investigate differences between predicted and measured coverage. HTZ Communications

Integrating indoor and outdoor planning

Campuses, airports and industrial sites often need coverage across buildings, outdoor work areas and the routes between them. HTZ Communications supports indoor, outdoor and mixed propagation studies, helping engineers assess where outdoor infrastructure provides sufficient coverage and where dedicated indoor equipment may be needed. Explore HTZ Communications and request a demo

Copyright © 2026 All Rights Reserved Privacy PolicyTerms and Conditions
Site designed by Fortico
Contact us

Request a software trial or demo

Register to receive a free trial licence or no obligation demo
Trial Licence
Request a demo
magnifiercrosschevron-down